STORAGE

The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool, well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Shelf Life 12 months unopened. Store indoors at 4.5°C (40°F) to 38°C (100°F).

INTENDED USE

Engineered specifically for the internal protection of onshore, offshore, and underground tanks and piping systems. It is applicable on the internal surfaces of chemical vessel storage, process water, wastewater, and grey water. Additionally, it is highly suited for fire protection lines, drilling mud tanks, and concrete safety walls.

Average Drying Times:

	15°C (59°F)	25°C (77°F)	43°C (110°F)
Touch	12 hours	4 hours	2 hours
Handle	20 hours	8 hours	4 hours
Recoat	20 hours	8 hours	4 hours
Cure	14 days	7 days	3 days
Pot life	—	2 hours	—

Drying time is temperature, humidity, and film thickness dependent.

COLOR & GLOSS VARIATION

Slight deviations in color may occur between production batches of primer and antifouling products. When subjected to atmospheric weathering and solar radiation, these products as well as epoxy-based topcoats, may exhibit chalking. Furthermore, the retention of gloss and color in topcoats depends on several factors. These include the paint type, specific pigment selection, application standards, and environmental conditions such as temperature and UV intensity.

ADDITIONAL NOTES

The product is for professional use only. Personnel shall be trained, experienced, and use the equipment to mix/stir well and apply the product properly. Applicators shall use appropriate personal protection equipment when using this product. Always comply with New Belmont Coatings LLC technical data.

WARRANTY

New Belmont Coatings LLC warrants our products to be free of manufacturing defects in accordance with applicable NBC quality control procedures. Liability for products proven defective, if any, is limited to replacement of the defective product or the refund of the purchase price paid for the defective product as determined by NBC.

DISCLAIMER

The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of New Belmont Coatings LLC. Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Published technical data and instructions are subject to change without notice. Contact New Belmont Coatings LLC for additional technical data and instructions.

STORAGE

The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool, well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Shelf Life 24 months unopened. Store indoors at 4.5°C (40°F) to 38°C (100°F).

INTENDED USE

High-resistance internal tank coating developed for chemical storage vessels. This is ideally suited for the protection of tanks containing grey water, drilling mud, brine, and crude oil and offers reliable protection against a wide array of chemical products. Engineered for internal lining applications across offshore, onshore, and underground infrastructure, ensuring long-term integrity in surface-level or buried installations.

Average Drying Times:

	4.5°C (40°F)	10°C (50°F)	25°C (77°F)	38°C (100°F)
Touch	14 hours	8 hours	3 hours	1 hour
Handle	20 hours	10 hours	4 hours	2 hours
Recoat	24 hours	12 hours	4 hours	2 hours
Cure	13 days	6 days	4 days	2 days
Pot life	4 hours	3 hours	2 hours	45 minutes

Drying time is temperature, humidity, and film thickness dependent.

SURFACE PREPARATION

Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.

Minimum recommended surface preparation: Iron & Steel: SSPC-SP6/NACE 3, 2 mil (50 micron) profile Stainless steel & Aluminum: Abrasive blast cleaning to achieve a surface profile using non-metallic abrasive media which is suitable to achieve a sharp and angular surface profile. Galvanizing: Sweep blast-cleaning using nonmetallic abrasive leaving a clean, rough and even pattern. Concrete: Dry abrasive blast cleaning to SSPCSP 13/NACE No. 6. Existing, aged coatings: SSPC-SP1 Solvent cleaning, then scarify / abrade the surface to ensure proper adhesion.

COLOR & GLOSS VARIATION

Slight deviations in color may occur between production batches of primer and antifouling products. When subjected to atmospheric weathering and solar radiation, these products as well as epoxy-based topcoats, may exhibit chalking. Furthermore, the retention of gloss and color in topcoats depends on several factors. These include the paint type, specific pigment selection, application standards, and environmental conditions such as temperature and UV intensity.

ADDITIONAL NOTES

The product is for professional use only. Personnel shall be trained, experienced, and use the equipment to mix/stir well and apply the product properly. Applicators shall use appropriate personal protection equipment when using this product. Always comply with New Belmont Coatings LLC technical data.

WARRANTY

New Belmont Coatings LLC warrants our products to be free of manufacturing defects in accordance with applicable NBC quality control procedures. Liability for products proven defective, if any, is limited to replacement of the defective product or the refund of the purchase price paid for the defective product as determined by NBC.

DISCLAIMER

The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of New Belmont Coatings LLC. Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Published technical data and instructions are subject to change without notice. Contact New Belmont Coatings LLC for additional technical data and instructions.

STORAGE

The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool, well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Shelf Life 12 months unopened. Store indoors at 4.5°C (40°F) to 38°C (100°F).

INTENDED USE

Developed for the protection of pipes and tanks used for drinking water. It is approved to meet the safety standards required for potable water storage.

Average Drying Times:

	10°C (50°F)	25°C (77°F)	43°C (110°F)
Touch	15 hours	10 hours	3 hours
Handle	25 hours	13 hours	5 hours
Recoat	25 hours	13 hours	5 hours
Cure	14 days	7 days	4 days
Pot life	—	30 minutes	—

Drying time is temperature, humidity, and film thickness dependent.

SURFACE PREPARATION

Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.

Minimum recommended surface preparation: Iron & Steel: SSPC-SP6/NACE 3, 2 mil (50 micron) profile Stainless steel & Aluminum: Abrasive blast cleaning to achieve a surface profile using non-metallic abrasive media which is suitable to achieve a sharp and angular surface profile. Composite: The surface shall be hand or machine abraded to impart a scratch pattern to the surface. Concrete: Dry abrasive blast cleaning to SSPCSP 13/NACE No. 6.

COLOR & GLOSS VARIATION

Slight deviations in color may occur between production batches of primer and antifouling products. When subjected to atmospheric weathering and solar radiation, these products as well as epoxy-based topcoats, may exhibit chalking. Furthermore, the retention of gloss and color in topcoats depends on several factors. These include the paint type, specific pigment selection, application standards, and environmental conditions such as temperature and UV intensity.

ADDITIONAL NOTES

The product is for professional use only. Personnel shall be trained, experienced, and use the equipment to mix/stir well and apply the product properly. Applicators shall use appropriate personal protection equipment when using this product. Always comply with New Belmont Coatings LLC technical data.

WARRANTY

New Belmont Coatings LLC warrants our products to be free of manufacturing defects in accordance with applicable NBC quality control procedures. Liability for products proven defective, if any, is limited to replacement of the defective product or the refund of the purchase price paid for the defective product as determined by NBC.

SUPPLEMENTARY DATA

Post-Curing Tank Sanitization Guide:

Once the coating has fully cured, the tank must undergo a thorough cleaning before entering service. While the Norwegian Institute of Public Health offers various approved methods, you may also utilize one of the following:

• Pressure Wash: Use fresh water at a minimum of 30°C (86°F).
• Steam Clean: Standard steam application across all surfaces.
• Manual Scrub: Use warm water combined with an alkaline detergent.

Final Rinse and Drying: Following the initial wash, flush all surfaces with clean, fresh water. For systems adhering to BS6920, ensure the coating is fully cured and rinsed prior to use.

Warm Water Systems: To optimize the cure for warm water use, maintain 23°C (73.4°F) for 7 days. Follow this with a 4-hour fresh water flush at a temperature sufficient to keep the steel at 50°C (122°F).

Critical Step: Pump the tank dry upon completion. Use rags or towels to remove any standing water. Do not allow water to evaporate, as this concentrates contaminants rather than removing them.

DISCLAIMER

The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of New Belmont Coatings LLC. Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Published technical data and instructions are subject to change without notice. Contact New Belmont Coatings LLC for additional technical data and instructions.