BELMONT EPIC
STORAGE
The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool, well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Shelf Life 24 months unopened. Store indoors at 4.5°C (40°F) to 38°C (100°F).
INTENDED USE
This silicone coating is suitable for all vessel types regardless of service speed, including slow or ultra-slow steaming ships and FPSOs. It is also recommended for use on propellers. The formula supports extended service intervals of up to 90 months and remains effective during long idle periods lasting up to 120 days.
RECOMMENDED SPECIFICATION
Typical Thickness / Recommended Spreading Rate per coat: Dry film thickness: 80 – 175 μm Wet film thickness: 114 – 250 μm Theoretical spreading rate: 8.5 – 3.89 m²/l
Average Drying Times:
| 10°C (50°F) | 20°C (68°F) | 30°C (86°F) | |
|---|---|---|---|
| Hard dry | 3.5 hours | 1 hour | 30 minutes |
| Handle | 21 hours | 8 hours | 6 hours |
| Cure | 14 days | 14 days | 14 days |
| Pot life | — | 60 minutes | — |
Drying time is temperature, humidity, and film thickness dependent.
SURFACE PREPARATION
Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.
Minimum recommended surface preparation: Existing, aged coatings: SSPC-SP1 Solvent cleaning, then scarify / abrade the surface to ensure proper adhesion.
COLOR & GLOSS VARIATION
Slight deviations in color may occur between production batches of primer and antifouling products. When subjected to atmospheric weathering and solar radiation, these products as well as epoxy-based topcoats, may exhibit chalking. Furthermore, the retention of gloss and color in topcoats depends on several factors. These include the paint type, specific pigment selection, application standards, and environmental conditions such as temperature and UV intensity.
ADDITIONAL NOTES
The product is for professional use only. Personnel shall be trained, experienced, and use the equipment to mix/stir well and apply the product properly. Applicators shall use appropriate personal protection equipment when using this product. Always comply with New Belmont Coatings LLC technical data.
UNDOCKING
Minimum undocking time depends on number of coats applied, film thickness, and prevailing temperature. Maximum undocking time depends on the exposure conditions, the degree of air pollution, etc. The most important factor is to carry out a thorough high-pressure, fresh water cleaning after prolonged exposure.
WARRANTY
New Belmont Coatings LLC warrants our products to be free of manufacturing defects in accordance with applicable NBC quality control procedures. Liability for products proven defective, if any, is limited to replacement of the defective product or the refund of the purchase price paid for the defective product as determined by NBC.
DISCLAIMER
The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of New Belmont Coatings LLC. Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Published technical data and instructions are subject to change without notice. Contact New Belmont Coatings LLC for additional technical data and instructions.
BELMOLISA
STORAGE
The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool, well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Shelf Life 18 months unopened. Store indoors at 4.5°C (40°F) to 38°C (100°F).
INTENDED USE
Ideal for underwater hull applications in both newbuilding and maintenance. This formulation is optimized for ships with diverse operational profiles, including varying speeds and activity levels. As part of a complete system, it provides a high-performance solution for service life periods lasting up to 60 months. Applicable to stationary offshore constructions and deep-water structures. It is a reliable solution for static assets requiring long-term immersion protection.
Average Drying Times:
| 4.5°C (40°F) | 10°C (50°F) | 25°C (77°F) | 38°C (100°F) | |
|---|---|---|---|---|
| Touch | 1 hour | 45 minutes | 30 minutes | 30 minutes |
| Recoat | 12 hours | 9 hours | 7 hours | 6 hours |
| Cure | 12 hours | 12 hours | 10 hours | 8 hours |
Drying time is temperature, humidity, and film thickness dependent.
SURFACE PREPARATION
Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.
Minimum recommended surface preparation: Immersion Service: SSPC-SP1 Solvent Cleaning Iron & Steel, bare: SSPC-SP10/NACE 2 (For anticorrosive primer coat) Existing Antifouling: SSPC-SP1 Solvent Cleaning. Rinse using high-pressure fresh water to remove any weak, outer layer of existing antifouling. Depending upon type of existing antifouling, a sealer coat may be recommended.
COLOR & GLOSS VARIATION
Slight deviations in color may occur between production batches of primer and antifouling products. When subjected to atmospheric weathering and solar radiation, these products as well as epoxy-based topcoats, may exhibit chalking. Furthermore, the retention of gloss and color in topcoats depends on several factors. These include the paint type, specific pigment selection, application standards, and environmental conditions such as temperature and UV intensity.
ADDITIONAL NOTES
The product is for professional use only. Personnel shall be trained, experienced, and use the equipment to mix/stir well and apply the product properly. Applicators shall use appropriate personal protection equipment when using this product. Always comply with New Belmont Coatings LLC technical data.
UNDOCKING
Minimum undocking time depends on number of coats applied, film thickness, and prevailing temperature. Maximum undocking time depends on the exposure conditions, the degree of air pollution, etc. The most important factor is to carry out a thorough high-pressure, fresh water cleaning after prolonged exposure.
WARRANTY
New Belmont Coatings LLC warrants our products to be free of manufacturing defects in accordance with applicable NBC quality control procedures. Liability for products proven defective, if any, is limited to replacement of the defective product or the refund of the purchase price paid for the defective product as determined by NBC.
DISCLAIMER
The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of New Belmont Coatings LLC. Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Published technical data and instructions are subject to change without notice. Contact New Belmont Coatings LLC for additional technical data and instructions.
BELMONAYA SL SPC
STORAGE
The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool, well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Shelf Life 24 months unopened. Store indoors at 4.5°C (40°F) to 38°C (100°F).
INTENDED USE
For use on prepared, underwater surfaces of steel vessels as a part of a complete coating system. Suitable for a wide range of operating environments and designed for life service protection up to 60 months.
Average Drying Times:
| 4.5°C (40°F) | 10°C (50°F) | 25°C (77°F) | 38°C (100°F) | |
|---|---|---|---|---|
| Touch | 1 hour | 30 minutes | 30 minutes | 15 minutes |
| Recoat | 9 hours | 8 hours | 4 hours | 2 hours |
| Cure | 16 hours | 10 hours | 8 hours | 4 hours |
Drying time is temperature, humidity, and film thickness dependent.
SURFACE PREPARATION
Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.
Minimum recommended surface preparation: Immersion Service: SSPC-SP1 Solvent Cleaning Iron & Steel, bare: SSPC-SP10/NACE 2 (For anticorrosive primer coat) Existing Antifouling: SSPC-SP1 Solvent Cleaning. Rinse using high-pressure fresh water to remove any weak, outer layer of existing antifouling. Depending upon type of existing antifouling, a sealer coat may be recommended.
COLOR & GLOSS VARIATION
Slight deviations in color may occur between production batches of primer and antifouling products. When subjected to atmospheric weathering and solar radiation, these products as well as epoxy-based topcoats, may exhibit chalking. Furthermore, the retention of gloss and color in topcoats depends on several factors. These include the paint type, specific pigment selection, application standards, and environmental conditions such as temperature and UV intensity.
ADDITIONAL NOTES
The product is for professional use only. Personnel shall be trained, experienced, and use the equipment to mix/stir well and apply the product properly. Applicators shall use appropriate personal protection equipment when using this product. Always comply with New Belmont Coatings LLC technical data.
UNDOCKING
Minimum undocking time depends on number of coats applied, film thickness, and prevailing temperature. Maximum undocking time depends on the exposure conditions, the degree of air pollution, etc. The most important factor is to carry out a thorough high-pressure, fresh water cleaning after prolonged exposure.
WARRANTY
New Belmont Coatings LLC warrants our products to be free of manufacturing defects in accordance with applicable NBC quality control procedures. Liability for products proven defective, if any, is limited to replacement of the defective product or the refund of the purchase price paid for the defective product as determined by NBC.
DISCLAIMER
The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of New Belmont Coatings LLC. Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Published technical data and instructions are subject to change without notice. Contact New Belmont Coatings LLC for additional technical data and instructions.
BELMOLISA SPC
STORAGE
The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool, well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Shelf Life 18 months unopened. Store indoors at 4.5°C (40°F) to 38°C (100°F).
INTENDED USE
Ideal for underwater hull applications in both newbuilding and maintenance. This formulation is optimized for ships with diverse operational profiles, including varying speeds and activity levels. As part of a complete system, it provides a high-performance solution for service life periods lasting up to 60 months. Applicable to stationary offshore constructions and deep-water structures. It is a reliable solution for static assets requiring long-term immersion protection.
Average Drying Times:
| 4.5°C (40°F) | 10°C (50°F) | 25°C (77°F) | 38°C (100°F) | |
|---|---|---|---|---|
| Touch | 1 hour | 45 minutes | 30 minutes | 30 minutes |
| Recoat | 12 hours | 9 hours | 7 hours | 6 hours |
| Cure | 12 hours | 12 hours | 10 hours | 8 hours |
Drying time is temperature, humidity, and film thickness dependent.
SURFACE PREPARATION
Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.
Minimum recommended surface preparation: Immersion Service: SSPC-SP1 Solvent Cleaning Iron & Steel, bare: SSPC-SP10/NACE 2 (For anticorrosive primer coat) Existing Antifouling: SSPC-SP1 Solvent Cleaning. Rinse using high-pressure fresh water to remove any weak, outer layer of existing antifouling. Depending upon type of existing antifouling, a sealer coat may be recommended.
COLOR & GLOSS VARIATION
Slight deviations in color may occur between production batches of primer and antifouling products. When subjected to atmospheric weathering and solar radiation, these products as well as epoxy-based topcoats, may exhibit chalking. Furthermore, the retention of gloss and color in topcoats depends on several factors. These include the paint type, specific pigment selection, application standards, and environmental conditions such as temperature and UV intensity.
ADDITIONAL NOTES
The product is for professional use only. Personnel shall be trained, experienced, and use the equipment to mix/stir well and apply the product properly. Applicators shall use appropriate personal protection equipment when using this product. Always comply with New Belmont Coatings LLC technical data.
UNDOCKING
Minimum undocking time depends on number of coats applied, film thickness, and prevailing temperature. Maximum undocking time depends on the exposure conditions, the degree of air pollution, etc. The most important factor is to carry out a thorough high-pressure, fresh water cleaning after prolonged exposure.
WARRANTY
New Belmont Coatings LLC warrants our products to be free of manufacturing defects in accordance with applicable NBC quality control procedures. Liability for products proven defective, if any, is limited to replacement of the defective product or the refund of the purchase price paid for the defective product as determined by NBC.
DISCLAIMER
The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of New Belmont Coatings LLC. Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Published technical data and instructions are subject to change without notice. Contact New Belmont Coatings LLC for additional technical data and instructions.