BELMOND EPIC SEALER

STORAGE

The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool, well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Shelf Life 18 months unopened. Store indoors at 4.5°C (40°F) to 38°C (100°F).

INTENDED USE

This is a high-performance tie-coat formulated for use as a mid-coat between epoxy anticorrosive products and silicone topcoat systems. It provides a chemically receptive surface for the silicone hydrogel.

Average Drying Times:

	10°C (50°F)	20°C (68°F)	30°C (86°F)
Hard dry	3 hours	2 hours	75 minutes
Handle	5 hours	4 hours	3 hours
Cure	10 days	7 days	4 days
Pot life	60 minutes	60 minutes	60 minutes

Drying time is temperature, humidity, and film thickness dependent.

SURFACE PREPARATION

Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.

Minimum recommended surface preparation: Existing, aged coatings: SSPC-SP1 Solvent cleaning, then scarify / abrade the surface to ensure proper adhesion.

COLOR & GLOSS VARIATION

Slight deviations in color may occur between production batches of primer and antifouling products. When subjected to atmospheric weathering and solar radiation, these products as well as epoxy-based topcoats, may exhibit chalking. Furthermore, the retention of gloss and color in topcoats depends on several factors. These include the paint type, specific pigment selection, application standards, and environmental conditions such as temperature and UV intensity.

ADDITIONAL NOTES

The product is for professional use only. Personnel shall be trained, experienced, and use the equipment to mix/stir well and apply the product properly. Applicators shall use appropriate personal protection equipment when using this product. Always comply with New Belmont Coatings LLC technical data.

UNDOCKING

Minimum undocking time depends on number of coats applied, film thickness, and prevailing temperature. Maximum undocking time depends on the exposure conditions, the degree of air pollution, etc. The most important factor is to carry out a thorough high-pressure, fresh water cleaning after prolonged exposure.

WARRANTY

New Belmont Coatings LLC warrants our products to be free of manufacturing defects in accordance with applicable NBC quality control procedures. Liability for products proven defective, if any, is limited to replacement of the defective product or the refund of the purchase price paid for the defective product as determined by NBC.

DISCLAIMER

The information and recommendations set forth in this Product Data Sheet are based upon tests conducted by or on behalf of New Belmont Coatings LLC. Such information and recommendations set forth herein are subject to change and pertain to the product offered at the time of publication. Published technical data and instructions are subject to change without notice. Contact New Belmont Coatings LLC for additional technical data and instructions.

BELMOSEAL

STORAGE

The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool, well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Shelf Life 48 months unopened. Store indoors at 4.5°C (40°F) to 38°C (100°F).

INTENDED USE

A high-performance tie-coat is formulated primarily for external hulls, underwater and boot-top areas. As a multi-surface compatible product is effective for protecting superstructures, decks, and other exposed surfaces, and is reliable for infrastructure, offshore assets and splash zones.

Average Drying Times:

	4.5°C (40°F)	10°C (50°F)	25°C (77°F)	38°C (100°F)
Touch	8 hours	5 hours	2 hours	1 hour
Handle	24 hours	18 hours	10 hours	6 hours
Recoat	24 hours	18 hours	10 hours	6 hours
Cure	7 days	5 days	3 days	2 days
Pot life	—	—	2 hours	—

Drying time is temperature, humidity, and film thickness dependent.

COLOR & GLOSS VARIATION

ADDITIONAL NOTES

WARRANTY

DISCLAIMER

BELMOPRIME

STORAGE

The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool, well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Shelf Life 48 months unopened. Store indoors at 4.5°C (40°F) to 38°C (100°F).

INTENDED USE

For atmospheric use on interior and exterior exposed areas, over properly primed steel and aluminum substrates.

Average Drying Times:

	4.5°C (40°F)	10°C (50°F)	25°C (77°F)	38°C (100°F)
Touch	4 hours	3 hours	3 hours	1 hour
Handle	28 hours	22 hours	6 hours	4 hours
Recoat	28 hours	22 hours	16 hours	10 hours
Cure	10 days	7 days	7 days	4 days

Drying time is temperature, humidity, and film thickness dependent.

SURFACE PREPARATION

Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.

Minimum recommended surface preparation: Iron & Steel: SSPC-SP6/NACE 3, 2 mil (50 micron) profile Aluminum: SSPC-SP1

COLOR & GLOSS VARIATION

ADDITIONAL NOTES

WARRANTY

DISCLAIMER

BELMEPOXY

STORAGE

The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool, well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Shelf Life 48 months unopened. Store indoors at 4.5°C (40°F) to 38°C (100°F).

INTENDED USE

This heavy-duty formula is ideal for marine maintenance and repair. Whether applied to exterior hulls or interior ship compartments, it provides a vital line of defense against saltwater and corrosion. It is recommended for massive infrastructure projects, including offshore environments, refineries, chemical power stations, mining machinery and equipment, bridges, commercial buildings, and general structural steel.

Average Drying Times:

	10°C (50°F)	25°C (77°F)	43°C (110°F)
Touch	8 hours	4 hours	2 hours
Handle	24 hours	10 hours	4 hours
Recoat	24 hours	10 hours	4 hours
Cure	14 days	7 days	2 days
Pot life	—	2 hours	—

Drying time is temperature, humidity, and film thickness dependent.

SURFACE PREPARATION

Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.

Minimum recommended surface preparation: Iron & Steel: SSPC-SP6/NACE 3, 2 mil (50 micron) profile Galvanizing: SSPC-SP1 Existing, aged coatings: SSPC-SP1 Solvent cleaning, then scarify / abrade the surface to ensure proper adhesion.

COLOR & GLOSS VARIATION

ADDITIONAL NOTES

WARRANTY

DISCLAIMER

BELMOGUARD

STORAGE

The product must be stored in accordance with national regulations. Keep the containers in a dry, shaded, cool, well-ventilated space and away from sources of heat and ignition. Containers must be kept tightly closed. Handle with care. Shelf Life 24 months unopened. Store indoors at 4.5°C (40°F) to 38°C (100°F).

INTENDED USE

This FDA-compliant epoxy is engineered for long-term endurance in cargo holds and on hatch coamings. Specifically formulated for cargo ballast holds, ensuring safety and performance in both dry and immersed conditions.

Average Drying Times:

	10°C (50°F)	25°C (77°F)	38°C (100°F)
Touch	5 hours	2 hours	1 hour
Handle	10 hours	5 hours	2 hours
Recoat	10 hours	5 hours	2 hours
Cure	14 days	7 days	4 days
Pot life	—	1 hour	—

Drying time is temperature, humidity, and film thickness dependent.

SURFACE PREPARATION

Surface must be clean, dry, and in sound condition. Remove all oil, dust, grease, dirt, loose rust, and other foreign material to ensure adequate adhesion.